Latest Trending Tech & Gadgets Lifestyle Apple Android

Everything Else

iOS 18 Tips, Tricks, How-Tos, News

How To: Replace the front oxygen sensor in a Saturn S series

Richpin's Auto Repair takes you through the steps of replacing the front oxygen sensor on a Saturn s-series vehicle. To begin replacing this sensor, you are shown how to remove the resonator box. Once the resonator box is removed you'll be shown a quick tip on how to make the removal of the oxygen sensor a little easier using PB Blaster spray. Next you'll be shown how to remove the electrical connector to the sensor and be given a suggestion on which tools are necessary to remove the sensor f...

How To: Replace the front crankshaft oil seal on a GM 3.1L V6

Richpin's Auto Care shows you how to replace the cam over seal on a GM 3.1L V6 engine. Once the vehicle is raised and is safely supported by jackstands, you'll be taken through the first step which involves removing the serpentine belt from the engine. After the belt is removed, the video shows you how to remove the splash shield in the wheel next to the engine, using the proper tool. Next you'll be removing the crank pulley using a pulley remover, allowing you to get access to remove the sea...

How To: Fix the wiring harness on a Ninja 250R motorcycle

The video describes the procedure of fixing the wiring harness on a Ninja 250R motorcycle. The person who owns the bike presents this video. He says that he got his bike back after getting the wire harness newly fitted. His signal blinker lights were not working. The next morning he wanted to make sure that it was fine. He plugged the wire and tried to switch it on, but it did not work. He also found that the horn was also not working. It was actually not working for a long time now. Then, he...

How To: Install a trunk override light switch in a Saturn car

In this video, Richpin demonstrates how to install a trunk override light switch in a Saturn car. When you open the trunk in a Saturn, the light turns on and there's no way to turn it off. Thus you must have a switch in the circuit so you can turn the trunk light off. Select an out of the way place to mount the switch so it doesn't interfere with your cargo. Find the blue connector. The red wire with the black stripe is the ground wire from the latch switch. First, disconnect the battery. The...

How To: Replace the windshield washer pump in a Saturn car

This video demonstrates how to replace the windshield washer pump in a Saturn S series car. Remove the reservoir by unscrewing the bolt and lift the reservoir and slide it back to take it off the mount. Disconnect the electrical connector by squeezing the clips and pull the connector off. Next remove the hose, making sure to cover the opening with the winger to prevent loss of fluid from the reservoir. Drain the fluid from the reservoir as shown. Get the pump off the reservoir by tapping the ...

How To: Seal a nitro engine

In this video tutorial, viewers learn how to seal a nitro engine. Nitro Engines are used for R/C models. This video will help viewers learn how to protect a nitro engine from air leakage. The video provides all the materials required to seal the nitro engine. The materials required include: automotive gasket material, green slime lube and screwdrivers. This video will benefit those viewers who have an R/C model and would like to learn how to seal the nitro engine.

How To: Inspect a motorcycle for damage after an accident

This video teaches viewers on how to inspect a motorcycle for damage after an accident as well as documenting it. The most important thing you need to do after an accident is to document all parts of the damage by taking photos of the damaged parts. Start by verifying the VIN number or Vehicle Identification Number and take a picture of it, take a photo of it. After that, get a photograph of the mileage on the dash area of the motorcycle. If there is other important information that needs to ...

How To: Solder & heat shrink wires

This is how to solder wires properly and then heat shrink them in order to insulate them. Firstly upkeep of the soldering iron is required to keep it from oxidizing. Portable versions of the iron are also available to make work more convenient. A solder sucker is required to suck up and solder left behind by the iron. Alternatively you could use a solder wick which when used with the solder iron can absorb all the solder over the circuit board. Onto the actual process, strip off some of the w...

How To: Remove the inner wheel bearing race on a front wheel drive car

Richpin demonstrates how to remove the inner wheel bearing race on front wheel drive cars. If you have pressed the wheel bearing off the hub and you want to reuse the hub, you need to remove the inner wheel bearing race. Use an air chisel to remove the inner wheel bearing race. First, make sure to wear a pair of safety goggles. Then, place a blunt chisel bit into the recess and remove the race. This can also be accomplished by working a regular chisel back and forth. If the chisel nicks the h...

How To: Identify a Jeep rear axle in order to replace it

RichPin shows how to identify a rear axle on a Jeep Grand Cherokee to determine the correct replacement part. The first thing to do is to identify the axle by cleaning the fill plug on the back cover. Look at the inscription of the plug to find out the style of the rear end. In this example, Rich has a "Dana" style rear end. To determine if it is a 35 or 44 Dana, look at the web area to the right of the plug to locate the number. The two steps outlined in this video allow you to identify the ...

How To: Put a spare tire on your car when you get a flat

Graham from TV Lesson explains how to change a tire. In most cars, the spare tire is located in the trunk, along with the jack and tools. First, look under the car and locate the folded pieces of metal to find the jack point. Raise up the jack a bit and slide it under the jack point. Next, using the lug wrench, break the torque on the lug nuts. Then, jack up the car. Once the car is jacked up, remove the lug nuts. Next, remove the flat tire and place it into the trunk of the car. Place the do...

How To: Perform a coolant flush

Let's try it on a G-35. The things needed are 2 gallons of engine ice and distilled water, engine flush, drain pan, funnel, safety glasses and some bags. First, remove the radiator cap and drain off the radiator, then re-instal the drain plug. Add one bottle of engine flush, distilled water, then re-instal radiator cap and run engine for 20-30 minutes. Allow engine to cool and the repeat the previous steps using only distilled water until water is present during draining. Then add engine ice ...

How To: Seal a leaky RV roof with EternaBond tape

In this how-to video, you will learn how to seal a leaky RB roof with EternaBond tape. First, you must have EternaClean to remove any old dirt or grime around the roof. Spray it and remove with a piece of cloth. Cut the tape into the sizes you may require. Lay them out and prepare the surface using EternaPrime. Place the EternaBond tape where you want it, as it will not come off once placed. Rub bubbles or creases out. Wider tape may be considered for bigger jobs. By viewing this video, you w...

How To: Replace an engine coolant tempature sensor on a Saturn

Richpin shows the proper way to replace an engine coolant temperature sensor on a Saturn S series. Before he explains the steps of replacing the sensor, Richpin covers the tools to use. Also, Richpin illustrates the types of tools to avoid before beginning the replacement process. First, remove the cap from the expansion tank and then tighten it the way it was before. Next, Richpin shows the procedure for locating the temp sensor. Then, remove the connector from the sensor. Afterwards, Richpi...

How To: Check and set your tire pressure

This how-to video is about how to check and set the tire pressure in the car. The first and foremost thing we need to consider while setting the right pressure in the car tire is looking for the proper inflation pressure for both front and rear tires. We can find the manufacturers specification for tire inflation near the driver side door, where the tire pressure for both the front and rear tires will be mentioned, take a correct look at the tire pressures. In this video the tire pressure req...

How To: Change a dirt bike tire

To change a dirt bike tire follow these instructions. First use the crescent wrench set to loosen, and remove the axle bolt from the wheel you are working on. Then, slide the wheel out of the stays and lay it flat on the ground in an open area. Use the screwdriver to let the air out of the tire by depressing the valve stem with the blade. Now place the palm of your hand on the tire next to the very edge of the rim, and forcefully push downward. If all of the air is out of the tire and you do ...

How To: Perform a brake inspection

Removing a vehicle's tires and inspecting the brake rotors is possible with a few easy steps. First, remove all five lug nuts and remove the wheel from the vehicle. A power tool will easily remove the lug nuts. You now have access to the wheel so the next order of business is to lift off the wheel. Once the wheel is off the vehicle and safely set aside, return to the vehicle. You now have access to the brake pad. The final step in the process is to inspect the brake pad for thickness and abno...

How To: Cut a rotor

Before cutting the rotors select a centering cone that fits about halfway through the center hole of hub-less rotor or bearing spacer to center the rotor to the spindle. After select two identical clamps that fit the rotor without interfering with the machined surfaces of the rotor. Slide one clamp onto lathe shaft, open end out Slide spring, followed by centering cone. Slide on the rotor and outer clamp followed by the bushing, spacer, and nut. Tighten nut and Install damping strap. Adjust t...

How To: Change a flat tire on your car easily

In this video NAIT automotive instructor Darren Jones instructs you on how to . First pull over at a safe location where the traffic is less where there is a firm surface underneath the vehicle. Put the vehicle into park and apply the parking break as shown. Use the owner’s manual to locate the equipment to change the tire and how to do it. Block the wheel that opposite the flat wheel as shown and loosen the lug nuts by half a turn, jack up the vehicle referring to the manual. Remove the lug ...

How To: Put a spare tire on your car

In this video it is demonstrated how to put a spare tire in your car if any of your tire is flat. First of all you should turn your car off and take out your auto manual to find out the location of spare tire and tool kit. Once you know that, take out the spare tire and the tools (mainly jack and spanner). With the help of the spanner loosen the screws in the tire. Then, with the help of a jack , raise your car a bit above the ground. Then take off the loosened screws from the tire and remove...

How To: Jump start a dead car battery

Opps! Left my lights on again. Luckily watching this video by Eric the Car Guy will help you learn how to jump start you car and get you ready to get back on the road without waiting for AAA. This video with clear instructions show you the safe way to jump start a car from another car. You'll learn how to attach the jumper cables and get the battery to recharge the right way. Eric will help you get your car running and back out on the road in no time!

How To: Use jumper cables to jump start a car

This video explains how to use jumper cables to jump start a car. First, determine that a dead battery is the reason your car is not starting. If the engine cranks when you turn the key, the problem is not the battery and jump-starting won't help. If the windshield wipers, lights and heater blower all work, the battery is probably fine and you may have a bad starter. A jump-start won't help if you have a bad starter. If you hear no sound at all when you turn the key or if the engine cranks ve...

How To: Diagnose and jump start a dead battery

Ever been stuck on the side of the road with no clue how to use those jumper cables in your trunk? Chris on WatchMojo will show you how to diagnose the problem, and the safe way to hook up those jumper cables, get the battery working again, and get you on your way. This step by step instructional video will walk you through each step on jumping your car. You will need a set of jumper cables and another working car to complete the jump.

How To: Understand jump starting a car

A car that needs to be jump started is going to make a clicking noise but things such as the lights and radio will not turn on. To jump start the car first you need to line the cars up so that the batteries are in line with each other. You will need a working car to jump the car that has the dead battery and a set of working jumper cables. Make sure both cars are completely turned off. Make sure that you keep the two sides of the jumper cables a part. You don't want the two sides of the cable...

How To: Clean a moped carburetor

This video shows you exactly how and what you need to know to clean your vintage moped carburetor. You'll get a quick overview of the mopeds workings, everything you need to do to make sure you keep your moped in take and give it the proper maintence it needs. Vintage bikes tend to build rust and water which you'll need to clean out to make sure your bike runs perfectly. This is an quick and easy fix to upkeep your bike and make sure it remains nice and clean.

How To: Check fuel pressure regulators for leaks on GM engines

A leaking fuel pressure regulator can cause your car or truck to be hard to start or die out. This may give a check engine light, also. It's a very common problem on many Chevy, Buick, Pontiac, and Oldsmobile 3.1L - 3.4L V6 engines. These are also know as the 3100 and 3400. Misfire codes P0300 and oxygen sensor codes will be stored in the computer memory. So, if you want to learn how to check your fuel pressure regulator for leaking gas on GM engines, then this video tutorial is for you.

How To: Replace the electric fuel pump in a Chevy Tahoe

Don't let an overpriced mechanic take control of your Chevy Tahoe repairs, learn to fix your car yourself. Learn from an ASE certified Master Automobile Technician with over 14 years of experience. He'll teach you how to replace the electric fuel pump in a Chevy Tahoe. This step-by-step video tutorial will show you the exact actions to make when replacing the fuel pump. Pay for only parts and use your own time!